How to fill the charger -free razor: 5 DIY method

Electric scooters of Razor is a major choice for riders that appreciate reliability and performance. But what if you mislead the charger? Knowing How to fill the burst -free razor can be useful in emergencies.

This guide will help you explore alternative methods and solutions, ensuring that you never get stuck without driving.

In this guide, we will break different types of scooter burst chargers and where to find replacements. We will also explore creative DIY charging solutions in case you do not have the original charger at hand.

What kind of charger does your razor need?

Most Scooters from the razor (E series and C series) Use 3 carat chargers that come out either 24V or 36V. These chargers have a separate filling brick. Cheaper models, such as Core 90, can use a simpler 12 V -free charger.

Buying a new charger

Fortunately, it is easy to find replacement chargers for razor scooters. When you buy it, make sure it has the exact voltage and the type of tooth for your scooter. You can check these details in a scooter manual or on the manufacturer’s website before buying.

Filling the scooter razor without a conventional charger

If you don’t have your scooter charger at hand, don’t worry! There are several DIY methods you can try to keep your scooter.

A. Separate and fill the battery

The battery of your razor scooter is the heart of her performance. If you are without a charger, one alternative is to remove the battery and charge it separately. Here’s how:

How to turn off the battery

You don’t need advanced tools – just a little patience. Follow these steps:

Take off on deck: Find the deck that covers the battery and remove the four screws that attach it.

Separate the battery terminals: Once the plate is off, find the battery. Carefully turn off the positive and negative terminals from the controller and for filling.

Remove the battery: Gently lift the battery from your section. You are now ready to explore alternative collection ways.

1. Charging with variable power

If you do not have your original scooter charger from the razor, a variable power can be a great alternative. Here’s how to use it safely:

Step 1: Connect to the battery

• Attach a positive power wire to a positive battery terminal and a negative wire to a negative terminal.
• In some cases, a polarity check may be required to ensure the correct connections.

Step 2: Adjust the voltage and electricity

• Set the voltage to match your scooter battery specifications.
• Adjust the electricity to about 10-15% of the AMP-SATE (AH) battery assessment. For example, if you have a 7AH battery, place the electricity on 1Ah.

Step 3: Following time tracking

• Charging usually lasts between 6 and 12 hours, depending on your scooter model.
• Once it is completely filled, carefully turn off the power and reconnect the battery with the scooter.

2. Charging with a car battery jumper

The car battery salesman can also be used to fill your scooter battery in an emergency. Follow these steps:

Step 1: Activate the jumper

• Turn on a car jumper to start sending electricity in the battery.

Step 2: Follow the filling process

• Allow the battery to be full for about 20 minutes.
• Check the battery temperature regularly – if it starts to heat, more than half of the charged are probably more than half.

Step 3: Prevent overheating

• Do not allow the battery to overheat as excess heat can damage the cells. If the battery is too warm, turn it off immediately to prevent the risk of overheating.

B. Direct charging through the recharge port

If you do not have your original razor scooter charger, you can still fill your scooter directly using a filling connection. Here are three alternative methods to turn on the battery and ready to drive.

1. Using a compatible charger and a joint cable

If you have a charger with the correct voltage (24V or 36V, depending on your scooter model), you can use it as a replacement.

How to do it:

• Cut a cable: Carefully cut the filling cable with a knife or wire cutter.
• Identify wires: You will find three wires – neutral, live and possibly Earth’s wire.
• Connect to the charging connection:
  • Attach live wire on to the right charging port.
  • Attach neutral wire on Left lateral pin charging port.
  • IN upper pin is a doll and does not require any relationship.

2. Charging a bank or solar charger

If you have a power supply bank or a solar charger with a correct voltage output, you can use it to fill the scooter directly.

How to do it:

• Choose the right charger: Ensure that a power supply bank or a solar charger comes out 24V or 36V, a corresponding battery of your scooter.
• Use a compatible cable: Connect the charger to the filling connection to the scooter filling with a suitable connecting cable.
• Start filling: Have a power supply bank or a solar charger fill your scooter battery.

This method is especially useful when you are outdoors or movement.

3. Charging a laptop or car charger

If you are in your finger, you can use a laptop or car charger as a temporary solution.

How to do it:

• Use a USB cable: Include one end in your laptop or car charger.
• Find the correct needles: Identify the live and neutral wires on the USB cable and connect them to the appropriate needles to the scooter filling connection.
• Check the voltage output: Laptop and car chargers usually go out 15V-20Vwhich may not fully fill your scooter, but it can give enough strength to take a short ride.

This is a great emergency option, especially if you are traveling with a laptop or driving.

Conclusion: How to fill a scooter from a razor -free razor

Maintaining a razor scooter is crucial to ensure smooth and without problems. Whether you use the original charger, replacement or creative with DIY solutions, there are many ways to be powered by your scooter.

You can manually exclude and fill the battery or use alternative power sources such as a variable power supply or laptop charger. These options come well when a standard charger is not available.